The Dinion IP Infrared Imager is a rugged, active infrared surveillance camera designed to master perimeter surveillance and other outdoor low-light applications. The IR Imager provides best-in-class images day and night covering up to 160 meters (525 feet) with unrivaled illumination quality throughout the field of view. The Dinion IP Infrared Imager can tri-stream video simultaneously — on two H.264 streams and one MJPEG stream. Features such as multicasting, internet streaming, and iSCSI recording are fully supported. The Dinion IP Infrared Imagers have built-in video motion detection and video content analysis systems as standard features.
|
Rated Voltage |
12 VDC (± 10%), 24 VAC (± 10%), 50/60 Hz, Power over Ethernet + |
Power Consumption |
|
at 12 VDC |
35 W (2.9 A) |
at 24 VAC |
35 W (1.5 A) |
Sensor |
|
CCD Type |
1/3-in. interline, WDR dual shutter |
Active Pixels: |
PAL: 752 x 582 NTSC: 768 x 494 |
Video |
|
Video compression |
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG |
Data rate |
9.6 Kbps to 6 Mbps |
Resolution |
Horizontal x vertical (PAL/NTSC ips) |
4CIF |
704 x 576/480 (25/30 ips) |
CIF |
352 x 288/240 (25/30 ips) |
Overall IP Delay |
Min. 120 ms, Max. 240 ms |
GOP structure |
I, IP |
Frame rate |
1 to 50/60 (PAL/NTSC) H.264 1 to 25/30 (PAL/NTSC) M-JPEG |
Video Out |
|
Signal |
Analog composite (NTSC or PAL), for use with OSD menus only4 |
Connector |
BNC, 75 Ohm |
Horizontal resolution |
540 TVL |
Video S/N |
50 dB |
4. The analog video output is active only when interacting with the imager’s OSD menus. Note that when analog video output is active, the IP video output is interrupted. |
|
Sensitivity (3200 K, scene reflectivity 89%, F1.2) |
|
Full video (100 IRE) |
Usable picture (50 IRE) , Usable picture (30 IRE) |
Color |
2.4 lx (0.223 fc) , 0.47 lx (0.044 fc) , 0.15 lx (0.0139 fc) |
Color + SensUp 10x |
0.24 lx (0.0223 fc) , 0.047 lx (0.0044 fc) , 0.015 lx (0.0014 fc) |
Monochrome |
0.98 lx (0.091 fc) , 0.188 lx (0.0174 fc) , 0.06 lx (0.0056 fc) |
Monochrome + SensUp 10x |
0.098 lx (0.0091 fc) , 0.019 lx (0.0017 fc) , 0.006 lx (0.0006 fc) |
Monochrome + IR Illumination |
0 lx (0 fc) , 0 lx (0 fc) , 0 lx (0 fc) |
Power |
|
PoE+ |
RJ-45 100 Base-TX Ethernet PoE+ IEEE 802.3at, class 4 |
Imager |
12 VDC/24 VAC (± 10%), 50/60 Hz |
Analog (video) |
PAL or NTSC BNC, for use with OSD menus only5 |
Video and Control |
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45 |
On-screen Display |
OSD with soft-key operation (multilingual) |
Alarm Output Relay |
30 VAC or +40 VDC, max. 0.5 A continuous, 10 VA Tamper: Open/close, normally closed voltage free relay |
5. The analog video output is active only when interacting with the imager’s OSD menus. Note that when analog video output is active, the IP video output is interrupted. |
|
|
|
Horizontal Resolution |
540 TVL |
Signal-to-Noise Ratio |
>50 dB |
Shutter |
Auto (1/50 [1/60] to 1/10000) selectable Auto (1/50 [1/60] to 1/50000) automatic flickerless, fixed selectable |
Sensitivity up |
Adjustable from Off up to 10x |
Day/Night |
Color, Mono, Auto Video, Auto Photocell |
Day/Night Photocell Control |
Day/Night switch adjustable: 25 lux to 64 lux (default at 48 lux) Night/Day switch adjustable: 43 lux to 82 lux (default at 63 lux) |
Auto Black |
Automatic continuous, Off |
Dynamic engine |
XF-Dynamic, 2X-Dynamic, SmartBLC |
Dynamic range |
120 dB (20-bit image processing) |
Dynamic Noise Reduction |
Auto, On/off selectable |
Sharpness |
Sharpness enhancement level selectable |
SmartBLC |
On (includes 2X-Dynamic ) / Off |
AGC |
AGC On or Off (0–30 dB) selectable |
Peak White Invert |
On/Off |
White Balance |
ATW, ATWhold and manual (2500 to 10000K) |
Alarm Output |
VMD or D/N and dedicated Tamper (for junction box) |
Cable Compensation |
Up to 1000 m (3000 ft) coax without external amplifiers (automatic set-up in combination with Bilinx coaxial communication) |
Camera ID |
17 character editable string, position selectable |
Test Pattern Generator |
Color bars 100%, Grayscale 11-step, Sawtooth 2H, Checker board, Cross hatch, UV plane |
Lens |
5–50 mm IR-corrected Varifocal auto-iris |
Angular Field of View(H x V) |
5 mm FOV: 51° x 40° 50 mm FOV: 6° x 4° |
Modes |
6 preset programmable modes |
Video Motion Detection |
One area, fully programmable |
Privacy Masking |
Four independent areas, fully programmable |
|
|
Protocols |
RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP V2/V3, ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP |
Encryption |
TLS 1.0, SSL, AES (optional) |
Ethernet |
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45 |
PoE+ supply |
IEEE 802.3at, class 4 |
|
|
Unit Configuration |
Via web browser or Configuration Manager |
Flicker Control |
50/60 Hz, selectable |
Software update |
Flash ROM, remote programmable |
|
|
LEDs |
7 SMT type LED array with Variable Field Illumination |
Beam Patterns (H x V) |
Wide beam: 42° x 10° (with 3D diffuser) Narrow beam: 10° x 10° |
Wavelength |
850 nm or 940 nm |
Intensity Adjustment |
31 step adjustments from min. to max. |
On/Off Control |
Slave to camera mode Manual on/off control via OSD and IP Interface |
Illumination Tilt Adjustment |
Maximum: 13° tilt above camera axis Minimum: 3° tilt above camera axis |
|
|
850 nm |
940 nm |
Range |
HFOI , Range , HFOI |
Detection |
160 m (525 ft) , 28 m (90 ft) , 80 m (260 ft) , 14 m (45 ft) |
Classification |
120 m (390 ft) , 21 m (70 ft) , 60 m (195 ft) , 10 m (35 ft) |
Recognition |
90 m (295 ft) , 16 m (50 ft) , 45 m (150 ft) , 8 m (25 ft) |
Identification |
50 m (165 ft) , 9 m (30 ft) , 25 m (80 ft) , 4 m (15 ft) |
|
|
850 nm |
940 nm |
Range |
HFOI , Range , HFOI |
Detection |
140 m (455 ft) , 24 m (80 ft) , 70 m (230 ft) , 12 m (40 ft) |
Classification |
105 m (340 ft) , 18 m (60 ft) , 52 m (170 ft) , 9 m (30 ft) |
Recognition |
80 m (255 ft) , 14 m (45 ft) , 40 m (130 ft) , 7 m (20 ft) |
Identification |
45 m (140 ft) , 8 m (25 ft) , 22 m (70 ft) , 4 m (10 ft) |
|
|
Dimensions (H x W x L) |
|
Camera and Bracket |
402 x 193 x 309 mm (15.8 x 7.6 x 12.2 in.) |
Total Assembly |
402 x 193 x 406 mm (15.8 x 7.6 x 16.0 in.) |
Weight |
|
Camera without Junction Box |
6.6 kg (14.5 lb) |
Junction Box |
1.4 kg (3.1 lb) |
Construction |
Corrosion-resistant aluminum |
Color |
RAL 9010 pure white with RAL 9005 jet black detail |
Finish |
Wet paint |
Window |
3.3-mm (1/8-in.) thick glass |
Bracket |
Corrosion-resistant, cable-managed |
Bracket Pan/Tilt Range |
Pan: ±90° Tilt: -48°/+44° |
Junction Box |
Separate from bracket allowing for wiring and cabling prior to camera installation |
|
|
Operating Temperature |
|
Standard6 |
–40°C to +50°C (–40°F to 122°F) |
With PoE+ Input6 |
–20°C to +50°C (–4°F to 122°F) |
Storage Temperature |
–40°C to +70°C (–40°F to 158°F) |
Operating Humidity |
20% to 100% (condensing) |
Storage Humidity |
up to 100% |
Weatherproofing |
Type 4X (NEMA 4X) and IP67 |
Solar Radiation |
Tested to MIL-STD-810F test standard for solar radiation (for A1 rated environments) |
6. Warm-up period required for cold start at –40°C (–40°F). |
|
|
|
1 |
Top , 3 , Side |
2 |
Front , 4 , Rear |
1 |
Corner Mount - Top , 3 , Pole Mount - Top |
2 |
Corner Mount - Side , 4 , Pole Mount - Side |